overclocked

Redid my hoses for better color scheme and adding a proper method to fill and drain the loop from the bottom pump/res so I can flush leak test and maintain the graphics card loop easier and better.
by Sparktite

Testing pump inlet tubing mod length and seeing if the sponge is even necessary with the mod....
by Sparktite

Testing some lighting for my acrylic water blocks, in short the white lights up too much and I'm already lining the case in white to show off parts and using UV strips for all the UV related things, the UV LEDs here aren't strong enough and show up too pu
by Sparktite

DSCF3058
by Rick Duff - Bremertonian

Can't afford another amazing dazmode uv led strip let alone another one and matching white strips from them as well so i made do with an old cold cathode 2pc with the 2 uv led strips, and an NZXT white sleeves led kit/cable for now. I even need to get ei
by Sparktite

Bleeding the system finally and gons start working on the lighting and cable routing this step took me far too long cuz I had to clean up one of my tool holders... A shot glass not like metaphorical tools literally tools Allen wrenches spares and darn thi
by Sparktite

Got some nice photos of the case as I pieced t back together some more for ideas and references again. Loving the look so far, overcompensating for the lack of white in the case itself for a mostly white themed color scheme by plasti dipping every possibl
by Sparktite

Color testing the blaze blue on a ram stick cover with a smoke plasti dipped window as the clear windows don't allow the led to glow through properly and seeing if adding more blue in would fit the theme better. Plus the plasti dip blaze colors look aweso
by Sparktite

Finally done time for the file and then re plasti dipping :P
by Sparktite

Work from the other day when trying to redo the top panel sadly couldn't get any good wet coats of the glossifier since my last can was spewing out plasti dip no matter the tip even after trying to take some of the pressure out it just did not wanna work
by Sparktite

Got some nice photos of the case as I pieced t back together some more for ideas and references again. Loving the look so far, overcompensating for the lack of white in the case itself for a mostly white themed color scheme by plasti dipping every possibl
by Sparktite

I think it's finally done now I just need to hook it all up and boot up windows so I can start working on a fresh install and move my additional ssd to a 6gb sata port over one of the wd 6tb drives probably my media drive. Still can't believe I managed to
by Sparktite

Sizing up the heatsinks and their respective beats leaders then I gotta figure out where everything should mount to and from. After that it's gonna be a lotta hoses and look just silly compared to a real clean non generic/sorta ghetto mobo water cooling s
by Sparktite

Redid my hoses for better color scheme and adding a proper method to fill and drain the loop from the bottom pump/res so I can flush leak test and maintain the graphics card loop easier and better.
by Sparktite

I think it's finally done now I just need to hook it all up and boot up windows so I can start working on a fresh install and move my additional ssd to a 6gb sata port over one of the wd 6tb drives probably my media drive. Still can't believe I managed to
by Sparktite

Holy crap I managed to find a way to dremel a flat cut into the security bit scuff made for their controller and I used a flathead to then remove the bit. I actually took apart a scuff now I can install all my precious custom parts that won't break down o
by Sparktite

Got some nice photos of the case as I pieced t back together some more for ideas and references again. Loving the look so far, overcompensating for the lack of white in the case itself for a mostly white themed color scheme by plasti dipping every possibl
by Sparktite

Got some nice photos of the case as I pieced t back together some more for ideas and references again. Loving the look so far, overcompensating for the lack of white in the case itself for a mostly white themed color scheme by plasti dipping every possibl
by Sparktite

Color testing the blaze blue on a ram stick cover with a smoke plasti dipped window as the clear windows don't allow the led to glow through properly and seeing if adding more blue in would fit the theme better. Plus the plasti dip blaze colors look aweso
by Sparktite

Test fitting the shelf into the mounting top for it, it's and unbelievably right fit but I had to do more work and dig around for the perfect screws and even bend the areas where the fan just refused to work with me and stop scripting the shelf it was mou
by Sparktite

So I just put the finishing touches in and I think it looks great just wish I had more uv cable combs/clips, I've got some black ones for the vid cards at the moment and then some white(uv) ones on the orange 24pin cables for now. I also still need to fin
by Sparktite

Oh man thank god i as able to go at this with a cutting blade instead of the usual aluminum oxide grinding bit, it'll make cleaning up and repainting a breeze and save me literally hours of work thank god.
by Sparktite

Color testing the blaze blue on a ram stick cover with a smoke plasti dipped window as the clear windows don't allow the led to glow through properly and seeing if adding more blue in would fit the theme better. Plus the plasti dip blaze colors look aweso
by Sparktite

Some quick pics of my test fitting parts n all now that all he Plasti dip work is done as far as I can tell. Now I just need to drill two holes for a specific fan get my lights and hosing better allocated and test run the loops for leaks n for looks befor
by Sparktite

Bleeding the system finally and gons start working on the lighting and cable routing this step took me far too long cuz I had to clean up one of my tool holders... A shot glass not like metaphorical tools literally tools Allen wrenches spares and darn thi
by Sparktite

Inside the PC
by SilentPenguin93

Mini folding party, Secret Headquarters, Los Angeles
by gruntzooki

Sizing up the heatsinks and their respective beats leaders then I gotta figure out where everything should mount to and from. After that it's gonna be a lotta hoses and look just silly compared to a real clean non generic/sorta ghetto mobo water cooling s
by Sparktite

So I just put the finishing touches in and I think it looks great just wish I had more uv cable combs/clips, I've got some black ones for the vid cards at the moment and then some white(uv) ones on the orange 24pin cables for now. I also still need to fin
by Sparktite

Got some nice photos of the case as I pieced t back together some more for ideas and references again. Loving the look so far, overcompensating for the lack of white in the case itself for a mostly white themed color scheme by plasti dipping every possibl
by Sparktite

Work from the other day when trying to redo the top panel sadly couldn't get any good wet coats of the glossifier since my last can was spewing out plasti dip no matter the tip even after trying to take some of the pressure out it just did not wanna work
by Sparktite

Holy crap I managed to find a way to dremel a flat cut into the security bit scuff made for their controller and I used a flathead to then remove the bit. I actually took apart a scuff now I can install all my precious custom parts that won't break down o
by Sparktite

Test fitting the shelf into the mounting top for it, it's and unbelievably right fit but I had to do more work and dig around for the perfect screws and even bend the areas where the fan just refused to work with me and stop scripting the shelf it was mou
by Sparktite

Dual Screen HDR
by SilentPenguin93

Trying to fit this fan shroud/grill piece to give the case more white, but it still needs to be shaved down on one side to fit so out comes the dremel. Gonna also be reworking my cpu block look and some of the wire routing and hosing now that a lot of the
by Sparktite

all the paint projects are drying their final coats and then it's time to file the shelf and get back to tidying up all the overspray and peeling on my door panels.
by Sparktite

Mini folding party 2, Secret Headquarters, Los Angeles
by gruntzooki

So I decided it'd be easier if I just reversed the flow of the whole graphics card loop so I got all the fitting on, so got myself the hosing color scheme to do and still gotta take the top back off and figure out exactly where my LEDs have to be placed..
by Sparktite

Can't afford another amazing dazmode uv led strip let alone another one and matching white strips from them as well so i made do with an old cold cathode 2pc with the 2 uv led strips, and an NZXT white sleeves led kit/cable for now. I even need to get ei
by Sparktite

Redid my hoses for better color scheme and adding a proper method to fill and drain the loop from the bottom pump/res so I can flush leak test and maintain the graphics card loop easier and better.
by Sparktite

Finally sanded down what a pain I wanna skip wet sanding/polishing and just try primer then rdy then plasti dip all over, besides the shelf is gonna be covered on both sides so whose gonna see right? Lol I hate doing macro-spec shit
by Sparktite

Showing the pump mounting and screw that got stuck to a spacer with pix before and after using the dip fix kit as well as a photo of the phanteks panel I wanna try drilling a hole into for hiding wires in the case otherwise I'll just remove the piece enti
by Sparktite

Dual Screen
by SilentPenguin93

Time for another PC work day hoping to get everything prepped for the transfer and disassembly of my current setup. Gonna start by getting the holes drilled out where I want them for my white radiator.
by Sparktite

So I decided it'd be easier if I just reversed the flow of the whole graphics card loop so I got all the fitting on, so got myself the hosing color scheme to do and still gotta take the top back off and figure out exactly where my LEDs have to be placed..
by Sparktite

I think it's finally done now I just need to hook it all up and boot up windows so I can start working on a fresh install and move my additional ssd to a 6gb sata port over one of the wd 6tb drives probably my media drive. Still can't believe I managed to
by Sparktite

Aw isn't she so cute wishing she was water cooled... No problem and mobo bad... U fix your CPU and or memory problem right now!
by Sparktite

Finished the card ages ago but finally got the pics up with some others of the single stick of ram I dipped blue and made a smoke window for to test two different lighting theories with. Got the other card in nicely customized too and then I'm finally rea
by Sparktite

Actually tearing it all down and planning to get as much of the move as I can under way I didn't really plan out how I was gonna maintain my main loop so I can't really even drain the thing without having to almost open the whole thing up to get to the ra
by Sparktite

Finally sanded down what a pain I wanna skip wet sanding/polishing and just try primer then rdy then plasti dip all over, besides the shelf is gonna be covered on both sides so whose gonna see right? Lol I hate doing macro-spec shit
by Sparktite

Work from the other day when trying to redo the top panel sadly couldn't get any good wet coats of the glossifier since my last can was spewing out plasti dip no matter the tip even after trying to take some of the pressure out it just did not wanna work
by Sparktite

Inside the PC
by SilentPenguin93

Actually tearing it all down and planning to get as much of the move as I can under way I didn't really plan out how I was gonna maintain my main loop so I can't really even drain the thing without having to almost open the whole thing up to get to the ra
by Sparktite

So I just put the finishing touches in and I think it looks great just wish I had more uv cable combs/clips, I've got some black ones for the vid cards at the moment and then some white(uv) ones on the orange 24pin cables for now. I also still need to fin
by Sparktite

Finally got a break to get some finishing touches started on the build before it goes back up on the wall. Luckily the problem before was a super quick fix so I'm hoping to sure everything back in without problems and the it's ready to go.
by Sparktite

General Look at the PC
by SilentPenguin93

So I just put the finishing touches in and I think it looks great just wish I had more uv cable combs/clips, I've got some black ones for the vid cards at the moment and then some white(uv) ones on the orange 24pin cables for now. I also still need to fin
by Sparktite

Finally loading everything into the case now that the fan on top aren't catching anymore... Here's some quick uv color examples still testing out the ram color combos, then a shot of the back cable arrangement and a shot of the PCI-E riser I'm using for m
by Sparktite

Can't stand the copper showing when there's no other visible copper. But I've decided to keep the xspc waterblock and back plate so long as I can plasti dip the back white which is being prepped. The swiftech AIO is all ready to go so gonna be taking the
by Sparktite

Nom Nom Nom (Red Ramshorn Snail)
by rmhowie